Error for Core2 + Env Pro?

[kingaza]

Describe the bug

I try the example ENV_PRO, by modifying for Core2.
But BME68X error of code 2 happpens.

To reproduce

Uploading ENV_PRO.ino…

Expected behavior

The official Core2 exmaple works, but the unit work fails.

Screenshots

Environment

• OS:
• IDE &IDE Version:
• Repository Version:

Additional context

No response

Issue checklist

• I searched for previous reports in the issue tracker
• My report contains all necessary details

[kingaza]

Rebooting...
ets Jul 29 2019 12:21:46

rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13964
load:0x40080400,len:3600
entry 0x400805f0
M5Core2 initializing...axp: vbus limit off
axp: gpio1 init
axp: gpio2 init
axp: rtc battery charging enabled
axp: esp32 power voltage was set to 3.35v
axp: lcd backlight voltage was set to 2.80v
axp: lcd logic and sdcard voltage preset to 3.3v
axp: vibrator voltage preset to 2v
touch: FT6336 ready (fw id 0x10 rel 1, lib 0x300E)
OK
BME68X error code : -2
Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled.

Core 1 register dump:
PC : 0x400880a4 PS : 0x00060a30 A0 : 0x800f7ba4 A1 : 0x3ffb1d90
A2 : 0x3ffb1da0 A3 : 0x00000988 A4 : 0x0000002e A5 : 0x3ffb1da0
A6 : 0x00000000 A7 : 0x00000002 A8 : 0x00000000 A9 : 0x3ffb1e80
A10 : 0x3ffb1f1c A11 : 0x00000000 A12 : 0x00000002 A13 : 0x0000ff00
A14 : 0x00ff0000 A15 : 0xff000000 SAR : 0x0000001e EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000988 LBEG : 0x400880a4 LEND : 0x400880c0 LCOUNT : 0x00000001

Backtrace: 0x400880a1:0x3ffb1d90 0x400f7ba1:0x3ffb1da0 0x400f7893:0x3ffb1e00 0x400d8ed5:0x3ffb1e30 0x400d24c6:0x3ffb1f50 0x400ddac6:0x3ffb2290

ELF file SHA256: 83434aaf8fc97b8a

[kingaza]

/**

• @file ENV_PRO.ino
• @author SeanKwok (shaoxiang@m5stack.com)
• @brief
• @Version 0.1
• @Date 2024-01-30
• @hardwares: M5Core + Unit ENV_PRO
• @platform Version: Arduino M5Stack Board Manager v2.1.0
• @dependent Library:
• M5UnitENV: https://github.com/m5stack/M5Unit-ENV
• BME68x Sensor library: https://github.com/boschsensortec/Bosch-BME68x-Library
• BSEC2 Software Library: https://github.com/boschsensortec/Bosch-BSEC2-Library
  */

#include <M5Core2.h>
#include <bsec2.h>

/**

• @brief : This function checks the BSEC status, prints the respective error
• code. Halts in case of error
• @param[in] bsec : Bsec2 class object
  */
  void checkBsecStatus(Bsec2 bsec);

/**

• @brief : This function is called by the BSEC library when a new output is
• available
• @param[in] input : BME68X sensor data before processing
• @param[in] outputs : Processed BSEC BSEC output data
• @param[in] bsec : Instance of BSEC2 calling the callback
  */
  void newDataCallback(const bme68xData data, const bsecOutputs outputs,
  Bsec2 bsec);

/* Create an object of the class Bsec2 */
Bsec2 envSensor;

/* Entry point for the example */
void setup(void) {
M5.begin();

/* Desired subscription list of BSEC2 outputs */
bsecSensor sensorList[] = {
    BSEC_OUTPUT_IAQ,          BSEC_OUTPUT_RAW_TEMPERATURE,
    BSEC_OUTPUT_RAW_PRESSURE, BSEC_OUTPUT_RAW_HUMIDITY,
    BSEC_OUTPUT_RAW_GAS,      BSEC_OUTPUT_STABILIZATION_STATUS,
    BSEC_OUTPUT_RUN_IN_STATUS};

/* Initialize the communication interfaces */
Serial.begin(115200);
Wire.begin(21, 22);

/* Valid for boards with USB-COM. Wait until the port is open */
while (!Serial) delay(10);

/* Initialize the library and interfaces */
if (!envSensor.begin(BME68X_I2C_ADDR_HIGH, Wire)) {
    checkBsecStatus(envSensor);
}

/* Subsribe to the desired BSEC2 outputs */
if (!envSensor.updateSubscription(sensorList, ARRAY_LEN(sensorList),
                                  BSEC_SAMPLE_RATE_LP)) {
    checkBsecStatus(envSensor);
}

/* Whenever new data is available call the newDataCallback function */
envSensor.attachCallback(newDataCallback);

Serial.println("BSEC library version " + String(envSensor.version.major) +
               "." + String(envSensor.version.minor) + "." +
               String(envSensor.version.major_bugfix) + "." +
               String(envSensor.version.minor_bugfix));

}

/* Function that is looped forever /
void loop(void) {
/ Call the run function often so that the library can
* check if it is time to read new data from the sensor
* and process it.
*/
if (!envSensor.run()) {
checkBsecStatus(envSensor);
}
}

void newDataCallback(const bme68xData data, const bsecOutputs outputs,
Bsec2 bsec) {
if (!outputs.nOutputs) {
return;
}

Serial.println(
    "BSEC outputs:\n\ttimestamp = " +
    String((int)(outputs.output[0].time_stamp / INT64_C(1000000))));
for (uint8_t i = 0; i < outputs.nOutputs; i++) {
    const bsecData output = outputs.output[i];
    switch (output.sensor_id) {
        case BSEC_OUTPUT_IAQ:
            Serial.println("\tiaq = " + String(output.signal));
            Serial.println("\tiaq accuracy = " +
                           String((int)output.accuracy));
            break;
        case BSEC_OUTPUT_RAW_TEMPERATURE:
            Serial.println("\ttemperature = " + String(output.signal));
            break;
        case BSEC_OUTPUT_RAW_PRESSURE:
            Serial.println("\tpressure = " + String(output.signal));
            break;
        case BSEC_OUTPUT_RAW_HUMIDITY:
            Serial.println("\thumidity = " + String(output.signal));
            break;
        case BSEC_OUTPUT_RAW_GAS:
            Serial.println("\tgas resistance = " + String(output.signal));
            break;
        case BSEC_OUTPUT_STABILIZATION_STATUS:
            Serial.println("\tstabilization status = " +
                           String(output.signal));
            break;
        case BSEC_OUTPUT_RUN_IN_STATUS:
            Serial.println("\trun in status = " + String(output.signal));
            break;
        default:
            break;
    }
}

}

void checkBsecStatus(Bsec2 bsec) {
if (bsec.status < BSEC_OK) {
Serial.println("BSEC error code : " + String(bsec.status));

} else if (bsec.status > BSEC_OK) {
    Serial.println("BSEC warning code : " + String(bsec.status));
}

if (bsec.sensor.status < BME68X_OK) {
    Serial.println("BME68X error code : " + String(bsec.sensor.status));
} else if (bsec.sensor.status > BME68X_OK) {
    Serial.println("BME68X warning code : " + String(bsec.sensor.status));
}

}

[kingaza]

wrong pin number for Core2 Wire:

#define SDA_PIN 32
#define SCL_PIN 33

Wire.begin(SDA_PIN, SCL_PIN);

[kingaza]

wrong pin number for Core2 Wire:

#define SDA_PIN 32
#define SCL_PIN 33

Wire.begin(SDA_PIN, SCL_PIN);